Gluing

The Turbo for the Industrial Adhesive (Reference 345576): The Activator Plus is a curing accelerator, which is specially adapted to the industrial adhesive. It allows in conjunction with the adhesive fast, crystal clear bonds on very small and / or imperfect surfaces on which no great pressure can be exerted. For bonding of porous and absorbent materials such. Wood, porcelain, leather, ceramics, clay, marble and more. best for. The already given by the adhesive tensile and shear force is increased again with the activator up to 30%. Content: 10ml, without expiration date. Application: Apply the activator on one side with the integrated brush. After a contact time of at least 20 seconds, apply our industrial adhesive to the counterpart (also on one side only) and join the parts together. The adhesive cures immediately upon contact with the activator. Tip: Depending on the application, it is also possible to apply the Activator Plus on one side, for example, to assemble the parts without adhesive and then to let the adhesive run into the break point with the aid of the micro capillary nozzle (fine dosing tip).

Practical set composition including glue JB Weld 2K, probably the strongest glue in the world. Included: • Dial milling device: Practical tool for replacing the dial feet on a dial. • Red hand oil dispenser • 20x dial feet 2.5 x 0.64 x 3.00 mm • 20x dial feet 2.5 x 0.69 x 3.00 mm • 20x dial feet 2.5 x 0.74 x 3.00 mm • 20x dial feet 2.5 x 0.79 x 3.00 mm • 20x dial feet 2.5 x 0.94 x 3.00 mm • JB WELD 2-component adhesive: Almost as strong as welded. Extreme adhesive, connects everything permanently. Waterproof, temperature resistant up to 300 ° C, solvent-free.

Der praktische Stick für die schnelle Reparatur! Montieren, kleben und abdichten mit dem HG Epoxy Stick Der Epoxy Stick ist eine Reparaturknetmasse, mit der du Ausbesserungsarbeiten schnell und einfach durchführst. Ein paar Minuten mit der Hand geknetet und diese unscheinbare Masse verwandelt sich in ein regelrechtes Universalgenie. Nach nur 5 Minuten ist das Material so fest, dass es sich kaum noch verformen lässt. Nach 24 Stunden ist die Masse so hart, dass man hineinbohren oder sogar ein Gewinde hineinschneiden könnte. Wofür wird das Epoxy eingesetzt? Der Dübel hält nicht mehr in der Wand? Kein Problem! Die Masse ein paar Minuten kneten und anschließend samt Dübel in das Loch pressen – fertig! Du hast ein Loch in der Regentonne? Kein Ding! Das Epoxy klebt sogar unter Wasser und dichtet deine Tonne wieder ab. Du sparst dir aufwendige Reparaturarbeiten. Du siehst also: Der Kreativität, das Epoxy sinnvoll einzusetzen, sind keine Grenzen gesetzt. Die Knetmasse eignet sich zum Montieren, Befestigen oder Abdichten. Nach dem Aushärten lässt sich die behandelte Stelle ohne Probleme schleifen, lackieren, bohren usw. Die Reparaturmasse ist abweisend gegen Wasser, Öl, Benzin und viele anderen Chemikalien. Temperaturbereich: -50°C bis +180°C (kurzfristig bis 300°C) Anwendung: 1. Reinigung Jeglichen Schmutz, wie Staub und Fett, von der zu behandelnden Oberfläche entfernen. 2. Folie abziehen Bevor mit der Knetmasse gearbeitet wird, muss die Schutzfolie rückstandslos entfernt werden. 3. Menge bestimmen Die benötigte Menge abschätzen und mit einem scharfen Messer vom Epoxy-Stick abschneiden. 4. Kneten Die benötigte Masse manuell mit der Hand kneten, damit sich die Inhaltsstoffe verbinden und eine Polymerverbindung eingehen (Tipp: Dabei Handschuhe tragen). Wenn das Material warm wird und sich verfärbt, bleiben ca. 5 Minuten zur Verarbeitung des Epoxids. 5. Reparieren und aushärten lassen Die Reparatur, wie z. B. das Abdichten von Löchern oder das Zusammenkleben kaputter Teile, vornehmen. Nach dem Aushärten kann das Material geschliffen, lackiert und angebohrt werden. 345870 - Epoxy-Stick - 56g • EIN UNIVERSALGENIE: Das HG Epoxy ist eine vielfältig einsetzbare Knetmasse zum Montieren, Kleben und Abdichten. • HÄLT AUCH UNTER WASSER: Das Epoxy eignet sich hervorragend zum Stopfen von Löchern und Abdichten von Tanks und Behältern. • BEARBEITBAR: Das Material wird so hart, dass sich die Stelle beliebig bearbeiten lässt. Du kannst sie schleifen, lackieren und anbohren. Gefahrenhinweis: ACHTUG. 4,4'-Methylen diphenyldiglycidylether. Reaktionsprodukte von Pentaerythrit, propoxyliertem und 1-Chlor-2,3- epoxypropan mit Schwefelwasserstoff. Verursacht Hautreizungen. Verursacht schwere Augenreizung. Kann allergische Hautreaktionen verursachen. Schädlich für Wasserorganismen, mit langfristiger Wirkung. Ist ärztlicher Rat erforderlich, Verpackung oder Kennzeichnungsetikett bereithalten. Darf nicht in die Hände von Kindern gelangen. Schutzhandschuhe / Augenschutz / Gesichtsschutz tragen. Bei Hautreizung oder -ausschlag: Ärztlichen Rat einholen / ärztliche Hilfe hinzuziehen. BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülen. Bei anhaltender Augenreizung: Ärztlichen Rat einholen / ärztliche Hilfe hinzuziehen.Inhalt/Behälter gemäß lokalen/nationalen Vorschriften der Entsorgung zuführen. Enthält epoxidhaltige Verbindungen. Kann allergische Reaktionen hervorrufen. UFI: 2E00-V04G-D00J-C2C4

Excellent adhesion with high temperature and weather resistance. For many applications in the home and workshop. Ideal for attaching dials and trim. Bridges uneven adhesive surfaces. Made of PE foam, 1 mm thick, 20 mm wide, 10 m long.

Features of the popular Hasufix with best value for money: - medium viscosity - colorless - cold-curing - one-component - Cyanoacrylate base - optimum strength values Wide range of applications: - jewelery and costume jewelery production - Manufacture of souvenirs, advertising and gifts - Modelling - Many industrial sectors such as electronics, watches, metrology - In the household and hobby: repair adhesive for toys, jewelry, cameras, shoes, handbags - Threadlocker - Gluing of rubber seals - Gluing in the interior of the vehicle The cyanoacrylate adhesive, like other products on the market (such as Bead Cord Glue) can be used as a special adhesive for threads, felt fabrics and threads. Knots or textile beads are permanently and elastically fixed on silk and nylon threads. If too much adhesive is used, Hasufix can outgas, as with almost all cyanoacrylate adhesives, and create a kind of "white veil". Therefore, not suitable for the bonding of rhinestones.

Features of the popular Hasulith Fashion Jewelry 1K Glue: - transparent-colorless - acid-free - dries glass - Adhesive edges barely visible in many applications - very good strength - quick drying Applications: - Costume jewelery - costume and bridal jewelry - Hair Accessories - Modelling - Arts and crafts articles - toys - Gift items - Decoration - Promotional items - Souvenirs u.v.m. Suitable for the bonding of - Metal, glass, ceramics, porcelain, stone, leather, wood, felt, textiles, cork, paper, cardboard, cardboard, plastics such as acrylic glass, ABS and cellulose acetate. - The adhesive is also suitable for bonding or gluing larger glass, rhinestones or Similisteinen (from Ø 5mm). For small stones please use the special 2K-stone glue with the order no. 330,100th - Not suitable is the Hasulith fashion jewelry adhesive for bonding polystyrene, PVC, PET, PP, nylon, rubber and other soft plastic types.

Special superglue without blooming effect! The new Hasulith Rapid Premium instant adhesive is the alternative for all jobs where no white coating, as usual with instant adhesives, can start. The advantages: - "Non-Blooming" feature - so no blooming / white veil effect around the splices - Perfect for all visible repair areas - low odor: no pungent smell, as you will find it with superglues - dries transparent - High adhesion - Ideal curing time: Fast, but with sufficient time for optimal positioning Customer review: "Super Glue, can be corrected excellent. Super also when repairing dials extremely well to use!". *** PLEASE NOTE IN APPLICATION *** In order to make handling of the sensational rapid glue non blooming even easier, the tip of the red-gray cap - as usual with other glues - must not be cut off. This is a resealable closure. Therefore: do not cut off! Open the transparent adhesive tip of the red-gray cap by turning this colorless part to the left (counterclockwise). (The colorless turning cap to the left, so that it "moves upwards.") The opening is activated and you can practically and easily dose the adhesive. After use, close again by turning the colorless glue tip to the right (clockwise) (until the resistance is reached). Also included is a separate "normal" white tip (if the original mechanism is eventually glued, the fastener itself was accidentally "destroyed", for example, by cutting off the tip, or you want to attach a cannula. under the white cap) must of course be cut off when used, by default the adhesive will be shipped with the red-gray attachment, in exceptional cases the white cap will be attached and the red-gray will be loose, in which case unscrew the white one Cap off and remove the underlying transparent cap from the opening (this is pressed in, by gently moving or with the help of a pair of pliers can easily remove this) and put / Rotate the red-gray cap on it and start at the above step.

Der wohl stärkste Kleber der Welt - Klebt, füllt und bindet jede Oberfläche - als würde man sie schweißen! JB Weld gilt als der stärkste Kleber der Welt! Er wurde vor 30 Jahren in den USA entwickelt und findet sich dort, millionenfach verkauft, in nahezu jedem Haushalt. Der 2-Komponenten Epoxydharz-Kleber ist universell einsetzbar und schafft wirklich dauerhafte Verbindungen. Ob Metall (wie z.B. Eisen, Stahl, Aluminium, Messing, Bronze, Kupfer, Zinn usw.), Holz, Glas, Keramik oder Kunststoff - JB Weld klebt alles - dauerhaft und superfest (die Zugfestigkeit beträgt 273 kg/cm²)! Nach dem Mischen der 2 Komponenten kann JB Weld 20-25 Minuten lang verarbeitet werden. Nach 24 Stunden ist das beste Klebeergebnis erreicht. Nun kann er - als wäre er aus Metall - gestrichen, lackiert, gesägt, gedübelt, geschliffen oder geschmirgelt werden. JB Weld schrumpft und reißt nicht während des Härtungsprozesses. Eine saubere Klebenaht bleibt sauber (wie beim Löten oder Schweißen), eine glatte Fläche bleibt glatt. Damit ist JB Weld überall dort ideal, wo hochpräzises Arbeiten erforderlich ist. Der ausgehärtete Kleber ist wasserfest, widersteht Temperaturen bis von -40 bis +290°C, Ölen, Säuren und Chemikalien (selbst Batteriesäure). Kann von den Händen während der Verarbeitung einfach mit Wasser und Seife abgewaschen werden. Riecht nicht, da ohne Lösungsmittel. Typische Anwendungen: • Heimwerken: Lecks in Armaturen und Abflüssen dichten, Zerbrochenes reparieren (Glas, Keramik, Holz, Metalle), verrostete Stellen ausgleichen, Risse und Löcher in Wänden füllen (und anschließend schmirgeln und streichen), lose Werkzeugstiele befestigen, lose Fliesen ankleben. • Auto: Mechanische Schäden z.B. am Getriebe oder Motorblock reparieren, Risse in Kunststoffteilen kleben (z.B. Stoßstange), Roststellen und kleine Beulen ausgleichen und anschließend lackieren. • Haushalt: Alle erdenklichen Klebearbeiten mit allen harten Materialien (Glas, Holz, Keramik, Metall) auch untereinander - klebt also z.B. Holz auf Metall. Vorteile auf einen Blick: • Verbindet dauerhaft Metall, Kunststoff, Keramik, Holz, Glas, Mauerwerk, etc. • Dichtet Rohre und Armaturen • Kleben statt schweißen, löten, dübeln • Kann gebohrt, lackiert, geschliffen werden • Temperaturbeständig von -40 bis +290° C • Wasserfest • Widersteht Ölen, Säuren und Chemikalien Testsieger bei Quarks&Co im WDR-Fernsehen: Ein 1,2 Tonnen schweres Auto wird über verklebte Aluminiumzylinder in die Luft gehoben. JB Weld reichte eine Klebefläche von nur 9,0 cm² und gewann so gegen die Konkurrenten von Loctite und Uhu. Selbst nach dem Öffnen noch 25 Jahre gebrauchsfähig! Bestes Klebeergebnis nach 24 Stunden. *** HINWEIS *** DAS VERPACKUNGSDESIGN KANN U.U. VON DIESER PRODUKTABBILDUNG ABWEICHEN, DER INHALT/ KLEBER IST JEDOCH DER GLEICHE WIE HIER BESCHRIEBEN. LIEFERUNG IM POLYBEUTEL STATT IM BLISTER!

here are plastics on the market, here you will be really mad if you try to glue them. This is due to the increased wax layer of these plastics these include, for example, PE or PP. (Like installed in children's toys, lunch boxes, etc.) If you try to glue such plastics without a primer, it only achieved a slight but no liability proper bonding. With this primer you can even wax-containing materials such as PE or PP permanently to bond again and bombproof together. Our advice to you: We recommend this adhesive to each weld from the bottle - the there comes a time where you encounter such plastics - and without these primers it is not possible to glue them successfully. PS: The primer has no expiration date, and is even cheaper by 20% in a set with 'the weld oit of the bottle'. 1. roughen surface & PRIMER APPLICATION In order for feeding the liquid primer deep, it is important to roughen the surface to be bonded something. A fine primer layer is then applied directly to the breaking point by means of the brush. The liquid then changed chemically the surface structure. 2. BONDING PROCESS PERFORM After a few seconds, the HG-primer has completed his work and evaporates. Now the actual bonding process can be carried out as usual. It should be noted that after applying the primer, the actual ultimate strength of the bond is reached after 24 hours.

Exclusive to Flume: A quick-drying special adhesive for bonding cords, tapes and tires made of rubber, soft PVC, nylon 6.6 or leather in metal closures (capsules, sleeves). The "capsule adhesive" or "closing" adhesive is perfect for bonding rubber or PVC tires in metal capsules. When bonding fashion jewelry ribbons or strips made of rubber or soft PVC in metal closures, the adhesive is characterized by optimum strength values. Put a drop of glue on the end of the tape, insert it into the sleeve and turn it so that the glue spreads well and fix for 1-2 minutes. Do not apply adhesive too thick (curing will otherwise be delayed considerably and will not achieve optimum strength). Reliably resilient after 30 minutes, fully loadable after three to six hours. Textile tapes can also be glued. The ends must first be immersed in zapon varnish (order number 326111) at least twice to reduce their absorbency. Allow the zapon varnish to dry before gluing. The adhesive is a medium-viscosity, colorless, cold-curing, one-component cyanoacrylate adhesive for the highest demands. In addition to the special importance in the bonding of capsules, e.g. On rubber straps, the adhesive is also used in model making and in many industrial sectors (eg electronics, watches, measurement technology). In the home and hobby sector, the capsule adhesive is used inter alia as a repair adhesive for toys, jewelry, cameras, shoes, handbags, for securing screws, for bonding rubber seals, in the automotive interior, etc. Especially suitable for: - almost all commercially available thermoplastic and thermosetting plastics (not PE and PP) - Natural and synthetic rubber, rubber, sponge rubber - Iron, steel, non-ferrous and light metals and their alloys, ceramics, stone, porcelain and much more. Not suitable for parts that are constantly exposed to water. Only conditionally suitable for absorbent or porous materials.

The drip tip, which is standard on the adhesive, can be exchanged for snap lock if required. The drip tip can be cleaned in acetone (several hours). Suitable for 10g, 20g and 50g containers.

For horizontal and vertical, point and line accurate, more economical dosages. The airtight sealing cap replaces the classic way of sealing the adhesive bottle with wax or a needle. Due to the tapered shape of the micro capillary nozzle can be shortened, whereby each specific desired tip diameter can be achieved. Suitable for all container sizes. Application: We recommend the use and storage with the micro capillary nozzle (fine dosing tip). Screw the microcapillary nozzle firmly onto the drip tip (conical). The adhesive can be applied with spot and line precision. After use, hold the bottle upright and pull the adhesive residue-free by gently pumping it onto the bottle belly. Then airtight with the closure cap belonging to the microcapillary nozzle. Our tip: Take 2 nozzles for each adhesive bottle, so you can use one for storage and the other for cleaning. If necessary, the micro capillary nozzle can be cleaned with acetone (several hours). Available as a unit with 2 pieces or 6 pieces.

Practical compilation from Industrial adhesive 10g (reference 345649) Fine dosing and dripping tip. (References 345579 and 345650) Our sets at a glance: Industrial Adhesive 10g - Special Filler - Fine Dosing and Drip Tip = 345656 Industrial Adhesive 20g - Special Filler - Fine Dosing and Drip Tip = 345655 Industrial glue 20g - fine dosing and dripping tip = 345654 Industrial glue 10g - fine dosing and dripping tip = 345653 Industrial Adhesive 20g - Activator Plus - Fine Dosing Tip = 345580 Industrial Adhesive 20g - Activator Plus - Universal Solvent - Fine Dosing Tip = 345581

Practical compilation from Industrial adhesive 20g (reference 345576) Fine dosing and dripping tip. (References 345579 and 345650) Our sets at a glance: Industrial Adhesive 10g - Special Filler - Fine Dosing and Drip Tip = 345656 Industrial Adhesive 20g - Special Filler - Fine Dosing and Drip Tip = 345655 Industrial glue 20g - fine dosing and dripping tip = 345654 Industrial glue 10g - fine dosing and dripping tip = 345653 Industrial Adhesive 20g - Activator Plus - Fine Dosing Tip = 345580 Industrial Adhesive 20g - Activator Plus - Universal Solvent - Fine Dosing Tip = 345581

Practical compilation from Industrial adhesive 20g (reference 345576) Special filler (reference 345651) Fine dosing and dripping tip (references 345579 and 345650) Our sets at a glance: Industrial Adhesive 10g - Special Filler - Fine Dosing and Drip Tip = 345656 Industrial Adhesive 20g - Special Filler - Fine Dosing and Drip Tip = 345655 Industrial glue 20g - fine dosing and dripping tip = 345654 Industrial glue 10g - fine dosing and dripping tip = 345653 Industrial Adhesive 20g - Activator Plus - Fine Dosing Tip = 345580 Industrial Adhesive 20g - Activator Plus - Universal Solvent - Fine Dosing Tip = 345581

Practical compilation from Industrial adhesive 10g (reference 345649) Special filler (reference 345651) Fine dosing and dripping tip (references 345579 and 345650) Our sets at a glance: Industrial Adhesive 10g - Special Filler - Fine Dosing and Drip Tip = 345656 Industrial Adhesive 20g - Special Filler - Fine Dosing and Drip Tip = 345655 Industrial glue 20g - fine dosing and dripping tip = 345654 Industrial glue 10g - fine dosing and dripping tip = 345653 Industrial Adhesive 20g - Activator Plus - Fine Dosing Tip = 345580 Industrial Adhesive 20g - Activator Plus - Universal Solvent - Fine Dosing Tip = 345581

Zweikomponentenkleber (Knetmasse), zum Füllen, Dichten und Kleben von Rissen, Fugen, Spalten, Kratzern und Löchern. Zum Überbrücken, Ausbessern, Formen, Befestigen, Instandsetzen und Verstärken. Ideale Haftung auf Metall, Stahl, Kupfer, Messing, Guss, Aluminium, Hart-PVC, ABS, Keramik, Stein, Beton, Holz, Glas, Gummi u.v.m. Der Kitt ist wasserfest, haftet auf feuchten Flächen, unter Wasser und weist eine sehr hohe Druckfestigkeit auf. Temperatur- (–50°C bis +280°C), alterungs- und chemikalienbeständig. Der Kitt kann nach Aushärtung problemlos mechanisch bearbeitet werden, wie bohren, schleifen, sägen, fräsen, gewindeschneiden und überlackieren. Der 2-Komponenten Schwanheimer Harz Kitt und Schwanheimer Härter Kitt ergeben einen festen, weitgehend alterungsbeständigen Formstoff mit guter Dimensionsstabilität. Der Ausdehnungskoeffizient ist ähnlich dem von Kupfer und Stahl. Anwendung: Den Klebstoff und den Härter (2-K, graue Masse) in der gewünschten Menge abschneiden und 1:1 durch Handwärme mischen (kneten). Bei einheitlicher Farbgebung (graugrün) innerhalb von 10 Minuten verarbeiten und mind. 2 Stunden bei Zimmertemperatur aushärten lassen. Beiliegende Gebrauchsanweisung beachten. Anwendungsgebiete: - Reparaturen von Maschinen, Fahrzeugen, Benzintanks, Ölwannen, Toren, Gittern, Geräten, Anlagen, Werkzeugen, Sanitäranlagen, Heizkörpern, Öfen, Fenstern und Türen

The jewelry glue set is a compilation of our products especially for the jewelery sector (goldsmiths, jewelers, etc.). This starter set is ideal for permanently and firmly connecting beads, gemstones, jewelry elements, pendant loops, chain links, chatons, end caps, knots, u.v.m. Basic set ideal for the start! Content: Reference 345576: Industrial Adhesive (20g), - Reference 345578: Activator Plus (10ml) and Reference 345579: 2 micro capillary nozzles. ************************************* INDUSTRY CEMENT: ************************************* One of the most popular adhesives in Germany: connects with and among each other permanently materials such as metal, wood, rubber, GRP, natural and synthetic rubber, ceramics, porcelain, stone, glass, plastic u.v.m. Solvent-free, 1-component adhesive, content 20g. Especially recommended by goldsmiths and jewelery designers, especially when used with Activator Plus (For porous materials such as gypsum, wood, clay, ceramics, leather (shoes), stone, etc.) For bonding where no pressure can be exerted (Model making, jewelry) or very high strength are required.) , Properties: - Fast drying, fast curing, easy processing - Suitable for transparent gluing on plexiglas, glass stones such as similis and zirconia, pearls and rubber - Without blooming - the sticky spot does not leave a white border and does not bloom - Bonding largely waterproof and resistant to moisture or chemicals - low viscosity - Temperature resistance: - 55 ° C to + 95 ° C - Stable over several years (TIP: The best storage can be achieved in the refrigerator with the capillary nozzles! (Do not store with the screw cap!) Application: The flat and exact surfaces of the parts to be bonded must be dry, free of rust, grease, dust and glue (pre-cleaning with cleaner reference 345577, for example). Adhesive one-sided and spotwise or thinly applied. By pressing the adhesive surfaces (contact pressure / oxygen removal), the bonding is initiated. Without pressure, a correction is possible for a short time. Let the glued parts rest for a few minutes without load, depending on the material, the final strength varies. It is recommended to carry out self-tests on the suitability. Opening, dosing and storage: Cut the tip of the bottle (drip tip) at the notch. Store vertically. For longer storage, close the drip tip airtight with the micro capillary nozzle (fine dosing tip) or candle wax. Protect adhesives from direct sunlight or heat. *************************************** *************************************** ACTIVATOR PLUS *************************************** The Turbo for the Industrial Adhesive (Reference 345576): The Activator Plus is a curing accelerator, which is specially adapted to the industrial adhesive. It allows in conjunction with the adhesive fast, crystal clear bonds on very small and / or imperfect surfaces on which no great pressure can be exerted. For bonding of porous and absorbent materials such. Wood, porcelain, leather, ceramics, clay, marble and more. best for. The already given by the adhesive tensile and shear force is increased again with the activator up to 30%. Content: 10ml, without expiration date. Application: Apply the activator on one side with the integrated brush. After a contact time of at least 20 seconds, apply our industrial adhesive to the counterpart (also on one side only) and join the parts together. The adhesive cures immediately upon contact with the activator. Tip: Depending on the application, it is also possible to apply the Activator Plus on one side, for example, to assemble the parts without adhesive and then to let the adhesive run into the break point with the aid of the micro capillary nozzle (fine dosing tip). **************************************** FEED OIL TIP / MICRO CAPILLARY NOZZLE **************************************** For horizontal and vertical, point and line accurate, more economical dosages. The airtight sealing cap replaces the classic way of sealing the adhesive bottle with wax or a needle. Due to the tapered shape of the micro capillary nozzle can be shortened, whereby each specific desired tip diameter can be achieved. Suitable for all container sizes. Application: We recommend the use and storage with the micro capillary nozzle (fine dosing tip). Screw the microcapillary nozzle firmly onto the drip tip (conical). The adhesive can be applied with spot and line precision. After use, hold the bottle upright and pull the adhesive residue-free by gently pumping it onto the bottle belly. Then airtight with the closure cap belonging to the microcapillary nozzle. Our tip: Take 2 nozzles for each adhesive bottle, so you can use one for storage and the other for cleaning. If necessary, the micro capillary nozzle can be cleaned with acetone (several hours).

The jewelry glue set is a compilation of our products especially for the jewelery sector (goldsmiths, jewelers, etc.). This starter set is ideal for permanently and firmly connecting beads, gemstones, jewelry elements, pendant loops, chain links, chatons, end caps, knots, and more Professional set ideal for the start! Content: Reference 345576: Industrial Adhesive (20g), - Reference 345578: Activator Plus (10ml) and Reference 345579: 2 micro capillary nozzles. ************************************* INDUSTRY CEMENT: ************************************* One of the most popular adhesives in Germany: connects with and among each other permanently materials such as metal, wood, rubber, GRP, natural and synthetic rubber, ceramics, porcelain, stone, glass, plastic u.v.m. Solvent-free, 1-component adhesive, content 20g. Especially recommended by goldsmiths and jewelery designers, especially when used with Activator Plus (For porous materials such as gypsum, wood, clay, ceramics, leather (shoes), stone, etc.) For bonding where no pressure can be exerted (Model making, jewelry) or very high strength are required.) Properties: - Fast drying, fast curing, easy processing - Suitable for transparent gluing on plexiglas, glass stones such as similis and zirconia, pearls and rubber - Without blooming - the sticky spot does not leave a white border and does not bloom - Bonding largely waterproof and resistant to moisture or chemicals - low viscosity - Temperature resistance: - 55 ° C to + 95 ° C - Stable over several years (TIP: The best storage can be achieved in the refrigerator with the capillary nozzles! (Do not store with the screw cap!) Application: The flat and exact surfaces of the parts to be bonded must be dry, free of rust, grease, dust and glue (pre-cleaning with cleaner reference 345577, for example). Adhesive one-sided and spotwise or thinly applied. By pressing the adhesive surfaces (contact pressure / oxygen removal), the bonding is initiated. Without pressure, a correction is possible for a short time. Let the glued parts rest for a few minutes without load, depending on the material, the final strength varies. It is recommended to carry out self-tests on the suitability. Opening, dosing and storage: Cut the tip of the bottle (drip tip) at the notch. Store vertically. For longer storage, close the drip tip airtight with the micro capillary nozzle (fine dosing tip) or candle wax. Protect adhesives from direct sunlight or heat. *************************************** ACTIVATOR PLUS *************************************** The Turbo for the Industrial Adhesive (Reference 345576): The Activator Plus is a curing accelerator, which is specially adapted to the industrial adhesive. It allows in conjunction with the adhesive fast, crystal clear bonds on very small and / or imperfect surfaces on which no great pressure can be exerted. For bonding of porous and absorbent materials such. Wood, porcelain, leather, ceramics, clay, marble and more. best for. The already given by the adhesive tensile and shear force is increased again with the activator up to 30%. Content: 10ml, without expiration date. Application: Apply the activator on one side with the integrated brush. After a contact time of at least 20 seconds, apply our industrial adhesive to the counterpart (also on one side only) and join the parts together. The adhesive cures immediately upon contact with the activator. Tip: Depending on the application, it is also possible to apply the Activator Plus on one side, for example, to assemble the parts without adhesive and then to let the adhesive run into the break point with the aid of the micro capillary nozzle (fine dosing tip). **************************************** FEED OIL TIP / MICRO CAPILLARY NOZZLE **************************************** For horizontal and vertical, point and line accurate, more economical dosages. The airtight sealing cap replaces the classic way of sealing the adhesive bottle with wax or a needle. Due to the tapered shape of the micro capillary nozzle can be shortened, whereby each specific desired tip diameter can be achieved. Suitable for all container sizes. Application: We recommend the use and storage with the micro capillary nozzle (fine dosing tip). Screw the microcapillary nozzle firmly onto the drip tip (conical). The adhesive can be applied with spot and line precision. After use, hold the bottle upright and pull the adhesive residue-free by gently pumping it onto the bottle belly. Then airtight with the closure cap belonging to the microcapillary nozzle. Our tip: Take 2 nozzles for each adhesive bottle, so you can use one for storage and the other for cleaning. If necessary, the micro capillary nozzle can be cleaned with acetone (several hours). ***************************************** UNIVERSAL SOLVENT AND CLEANER ***************************************** Removes and dissolves adhesives, adhesive residues and stubborn stains (such as red wine, permanent markers etc.) from hands, metal, porcelain, glass, Plexiglas, wood, plastics, clothing, upholstery and carpets - also ideal for pre-cleaning when using industrial adhesive, reference 345576 , Content: 10ml, without expiration date, store in dark place. Application: First check the material for compatibility at a hidden point! Depending on the degree of soiling, apply the dissolver and cleaner and allow to take effect. Remove the dissolved adhesive / stain with a clean cloth with circular movements. If necessary, repeat the process. When removing stains from clothing, it is recommended that you put under absorbent cloth. After finished use, thoroughly wet surfaces with water!

Eigenschaften: Der Primer Plus (Haftvermittler) ermöglicht in Verbindung mit unserem Industriekleber dauerhafte feuchtigkeits- und alterungsbeständige Verbindungen von schwer zu verklebenden Kunststoffen wie z.B. Silikon, PTFE (Teflon), PP (Polypropylen), PE (Polyethylen), POM (Polyoxymethylen) und ölhaltigen Thermoplasten. Anwendung: Den Primer mit dem integrierten Pinsel beidseitig auf die Klebeflächen auftragen. Nach einer Einwirkzeit von mind. 20 Sekunden unseren Industriekleber (Referenzen 345576/ 345649) einseitig auftragen und die Teile unter Druck zusammenfügen. Tipp: Sehr kleine Klebestellen anschließend mit unserem Spezial-Füllstoff Referenz 345649 verstärken. Haltbarkeit: Ohne Verfallsdatum. Dunkel lagern. Gefahrenhinweise: Gefahr GHS02 + GHS07 + GHS08 + GHS09 H225 Flüssigkeit und Dampf leicht entzündbar. H304 Kann bei Verschlucken und Eindringen in die Atemwege tödlich sein. H315 Verursacht Hautreizungen. H336 Kann Schläfrigkeit und Benommenheit verursachen. H411 Giftig für Wasserorganismen, mit langfristiger Wirkung.